Cisco 300-360 Exam Dumps Study Material - Exam4Help

Question: 1

Which two types of information must be included in the installation inventory portion of the postinstallation report? (Choose two.)

A. all AP, controller, and MSE administrator credentials
B. the names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the
WLAN
C. a layout of the rack that the equipment is installed
D. results of the coverage audit performed with the site survey mapping tool
E. the number and type of all WLAN clients and tags

Answer: A, B 


Question: 2

A customer wants to implement a wireless network in a historic location, but is concerned about the
structural and aesthetic impact to the facility. Which benefit of using wireless mesh addresses these
concerns?

A. Power is required only at the installation location.
B. The APs do not have LED lights.
C. More wireless channels can be supported.
D. APs do not need network connections.

Answer: D 


Question: 3

An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)

A. external connector access point
B. integrated antenna access point
C. coax low-loss cable
D. battery operated power supply
E. range finder
F. Yagi antennas

Answer: B, D, E 


Question: 4

Which three options are benefits of U-APSD? (Choose three.)

A. optimized power-save mode periods
B. increased call capacity
C. bandwidth reservation
D. synchronization of the transmission and reception of voice frames
E. efficient roaming
F. priority bandwidth and polling

Answer: A, B, D 


Question: 5

A customer has restricted the AP and antenna combinations for a design to be limited to one model
integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

A. Deploy the specified access points per area type.
B. Resurvey and adjust the design.
C. Increase the Tx power on incorrectly surveyed access points.
D. Deploy unsurveyed access points to the design.

Answer: B 



Question: 6

An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services. Which two requirements are inputs to the design? (Choose two.)

A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access point
E. continuous -72 dBm coverage from one access point

Answer: A, D 


Question: 7

The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm

Answer: B 


Question: 8 

A customer has dual-band devices that they want to use 40 MHz channels. If the customer is using Cisco 3600 Series access points with a 5508 controller. Which setting assists with this change?

A. Enable band select globally.
B. Enable aggressive load balancing.
C. Disable lower data rates on 802 .11G GHz radios.
D. Disable overlapping 802.11G channels.

Answer: A 


Question: 9

An engineer is tuning RRM parameters to improve client connectivity. Which channel band results in the best 802.11n client compatibility?

A. UNII-2
B. UNII-2e
C. UNII-3
D. UNII
E. UNII-1

Answer: E 


Question: 10

An engineer is assigned to assist a customer by estimating the number of access points needed to
provide voice-grade wireless coverage in a carpeted office space. How many access points should be
estimated to cover this space of roughly 38,000 square feet?

A. 17
B. 10
C. 6
D. 13

Answer: D